Li Jujube Tree

Immediately upon receiving a bare root tree, remove it from its box to make sure to inspect the roots and see that they are still moist. One way to keep roots damp is to give the roots a quick rinse and repack them in the packing material in which they arrived until you are ready to plant. Alternatively, the use of autumn leaves, wood chips, or even shredded newspaper will keep the roots damp until you are ready to plant.

Note that the roots should be fully covered and kept moist until you are ready to plant. Keep your tree cool (ideally between 30° and 40°F) to prevent the tree from breaking its dormancy until you are ready to plant. After wrapping the roots in packing material and plastic to hold in moisture, put the plant in a cool place away from the sun. Another way to hold a tree in good condition before planting is to heal it in. On the cooler side of your house, dig a shallow hole that is just deep enough for the roots and temporarily plant the tree there.

Just before planting time, inspect a tree’s roots, removing any that are dead, damaged, or diseased. Cleanly cutting frayed ends reduces the surface area of wounds, so that healing is quicker, and the risk of root damage is reduced. Keep the roots from drying out when taking a tree to its planting site by keeping it wrapped in moist cloth or newspaper.

Before digging a planting hole, scoop up a handful of dirt and squeeze it. If it’s ready for digging, the soil will be just moist enough to crumble readily. If the soil is too wet, wait for it to become drier. Digging soil that is too wet, especially one that is high in clay, ruins its crumbly structure. If it’s too dry, water it.

Dig the hole a little deeper than the root is tall and make it wide enough to accommodate the longest roots without bending.

Make sure that the hole is tapered from ground level at the edges to full depth at the center, like a wide, shallow cone. For easy root penetration, rough up the inside of the hole by poking it with a shovel and giving it a few twists.

If lime or sulfur is needed to change the pH of the soil, thoroughly mix it into the bottom of the planting hole. Both of these materials move slowly through the soil and take a long time to work their way down to the roots.

Do not mix fertilizer into the planting hole, since it could burn new roots. Also, do not add peat moss, compost, or other organic materials.

Shovel enough loose soil back into the planting hole to create a mound on which to set the tree. The top of the root ball should stand slightly higher in the soil, to allow for settling.

Backfill with native or slightly amended soil until the bottom of the hole is at the right planting depth for the tree. If multi-planting in one hole, backfill to correct planting depth for each tree.

Place your tree in the planting hole and backfill with native or slightly amended soil. Be sure that the graft is sitting at least a few inches above the final soil level. Once backfilled, the top of your root ball should be just below the native soil level.

Water your new tree. Slowly and thoroughly soak the ground and allow the water to seep in. Do this two times.

Once planted, water once per month until the tree breaks dormancy and begins to leaf out. IMPORTANT: Overwatering before the tree wakes from dormancy can kill your tree. Once the tree breaks dormancy and throughout its first growing season, diligently maintain a weekly watering schedule. One gallon per week per square-foot spread of the roots.

Prune the canopy of your tree at this time. The goal here is to have a canopy that is roughly as large as your root mass. By balancing the root mass with the canopy, you will see much less dieback on your branches and a higher success rate with your new tree. If you want the fruiting wood to begin low, smaller trees may be cut back at planting time to a height as low as the knee (15-20 inches). Any remaining side limbs should be cut back to one or two buds. Larger trees may be cut above existing well-placed low limbs, or they too may be cut back low to force new, lower limbs. If this step is skipped, you will likely see low vigor from the first season, dieback from these long branches, or even complete failure to break dormancy.

Protect the trunk of your tree from sunburn, pests, and insects with IV Organics Plant Guard tree paint and foliar spray. Paint your newly planted tree from the ground up. This step is particularly important for our growers in the southwest where the climate and the intense sun tends to damage trees.

Spread 3"- 5” of wood chips or straw over the bare ground. Keep mulch away from the trunk to prevent the trunk from rotting. This insulating blanket will keep the roots of the trees warm and growing and prevent freezing and thawing of the soil. It will also keep the roots of the trees cool and moist through summer.

Stake trees that stand over 3' tall or in very windy areas for at least a year until their roots grab a firm hold of the soil. Tie the trunk to one or two stakes set beside the tree, using some soft material or padded wire. Allow for some movement of the trunk.

Keep your circle of mulch weed-free for at least a few years, adding more mulch as needed.

With proper planting and care, new buds will soon push out and your tree will start its journey! If your tree does not break dormancy by May, you will want to check for signs of life on your tree. One of the best ways to determine if a tree or any plant is dead is the scratch test. With your nail, gently scratch off the top layer in a small spot on a branch or on the trunk. Just beneath the dry, outer layer of bark in a tree's trunk lies the cambium that transfers nutrients throughout the tree. In a living tree, this is green; in a dead tree, it is brown and dry.

If the tree is green and still living, stop watering for the next 14 days. Bare root trees have no leaves and no way to expel excess water. If your tree is dead or does not push after 14 days, contact your grower for more guidance.

Dormant Plant Guarantee: We guarantee that trees that are shipped dormant will leaf out the following spring if you follow our growing and handling instructions.  Any dormant tree that does not leaf out can qualify for a refund if you submit a claim by May 15^th.  All deciduous fruit trees, persimmons and jujubes need to be planted in the ground by April 1^st to qualify for replacement, unless you are in area where the ground is still frozen at that time.  

In the rare event that your dormant tree/plant has not leafed out by May 1st, please perform a “scratch test” to check for green under the bark.  Just beneath the dry, outer layer of bark in a tree's trunk lies the cambium layer.  In a living tree, this is green; in a dead tree, it is brown and dry. To perform a “scratch test”, scratch off the top layer of bark in a small spot on a branch and on the trunk.  Be sure to do 1 test above the graft union, and a 2nd just below the graft union.  If the scratch test reveals a brown cambium, that means your tree/plant is dead or dying. 

To qualify for a refund, you must submit a claim via email to cs@fourwindsgrowers.com by no later than May 15^th.  Please include your order number in the subject line of your email.  

Claims must include:

-Photos of the scratch test areas

-Your order number

-Name(s) of trees affected.    

We will review your claim and if approved, we will issue you a refund for the purchase price of your dormant tree (excluding shipping).  We reserve the right to not issue a refund for items that have already been replaced.